A. 產品包括(CONSIST OF) ;
1) Chamber part試驗機部件
2) Test Chamber試驗箱
3) High Temp. Chamber高溫箱
4) Low Temp. Chamber低溫箱
5) Instrument panel儀表板
6) Safety device**裝置
7) Recorder記錄器
A. 產品特征(Features) ;
1. Manufacturing testing equipment based on vacuum insulation for high insulated
performance.
使用隔熱性能高的(VIP)真空保溫材料制造的實驗機器。
2. Over eight times higher insulated performance compare to existing insulation.
比現有的保溫材料高出8倍以上的隔熱性能。
3. Maintaining the stable high precision for temperature and humidity.
對與溫度濕度能維持穩定的高精密度。
4. Reliable testing equipment based on vacuum insulation with environmental friendly and high insulated performance.
采用親環境高隔熱性能的真空保溫材料的信賴性試驗機。
5. Average diameter for silica basic particle of vacuum insulation is extremely small with 7~40nm and wide surface area with 50~380m2/g. Highest insulated performance display due to low thermal conductivity with three-dimensional type.
真空隔熱材料的硅石基本粒子的平均直徑為7~40mm，非常小，因為廣泛的表面積 (50~380m2/g)和三元形態的特性，熱傳導率非常低，可以發揮*佳的隔熱性能。
6. Vacuum insulation with thermal conductivity of less than 0.0045W/mK Strengthens over eight times insulated performance compare to the same thickness "GA" class insulation.
真空隔熱材料熱傳導率值為0.0045W/mK 以下，具有比同一厚度基準的 “甲”級隔熱材料高出8倍以上的隔熱性能 。
7. Reliable testing equipment based on vacuum insulation can reduce the thickness of insulated wall conspicuously due to maintaining over eight times for insulated performance compare to existing insulation and be more profitable for energy saving and utilization of the space and secure user space.
利用真空隔熱材料的信賴性試驗機器與原有的隔熱材料相比具有8倍以上的隔熱性能，減少隔熱壁體的厚度不僅帶來節能和利用空間的效果，而且還有利于確保使用空間。
B. 產品規格(Specification) ;
1) 試驗箱部件(Chamber part)- 內部材料 Material ( in): SUS 304 1.2T Polished plate- 外部材料 Material (out): SS41 steel plate & with baked coating finish- 隔熱材料 Insulations : Vacuum insulation for high insulated performance, Poly-urethane foam & glass wool真空隔熱材料(VIP), 聚氨酯 及玻璃纖維 。- 試驗箱門密封 Test door packing : 雙重硅酮密封 Double silicon packing
2) 試驗箱(Test Chamber)
- 內箱尺寸 Test chamber dimensions(IN): 400 x 400 x 400 (WxDxH)mm
- 外部尺寸 Test chamber dimensions(out): 1300 x 1650 x 1950 (WxDxH)mm
- 溫度實驗范圍 Test temp. range ;
* 低溫試驗Low temp. test : -70℃ ~0℃
* 高溫實驗High temp. test : 65℃ ~ 200℃
- 試驗時間 Test time:
* 低溫試驗Low temp. test: 30min
* 高溫試驗High temp. test : 30min
- 試驗恢復時間 Test restoration time:
* -50℃ ~ 150℃ : 5min
* 150℃ ~ -50℃ : 5min
- 溫度偏差范圍Temp. variation range : ±0.4℃
- 溫度均勻度 Temp. Uniformity: ±0.7℃
- 程序控制器 Program controller:
* 型號 Model : TS-500
* Display Mode : LCD cold touch screen
* 溫度設定范圍 Temp. setting range : -100℃ ~ 250℃
* 運轉模式 Operation mode : Fix value & Pattern program control
* Program pattern & repeat : 99 pattern / 2segment & 9999 cycle
* 警報功能 Alarm function
* 溫度感應器Temp. sensor : T - type
3) 高溫箱(High Temp. Chamber)
- 溫度控制范圍 Temp. range : 65℃ ~ 200℃
- 溫度上升比率 Temp. heat-up rate : RT ~ 220℃ within 30min
- 溫度加熱器 Temp. Heater : 12KW
- 循環電機 Circulation motor : AC 380V 3P 50Hz 600Wx2
4) 低溫箱(Low Temp. Chamber)
- 溫度控制范圍Temp. range : 0℃ ~ -70℃
- 溫度上升比率Temp. heat-up rate : RT ~ -70℃ within 45min
- 溫度加熱器Temp. Heater : 6KW
- 循環電機 Circulation motor : AC 380V 3P 50Hz 600Wx2
- 雙重結冰系統 Dual freezing system
- 冷凍壓縮機 Refrigerator: Compressor 15HP x 2 SET
- 冷卻系統 Cooling system: AIR COOLED TYPE
- 制冷劑 Refrigerant : HFC 404a, HFC 23
5) 儀表板(Instrument panel)
- 溫度程序控制器Program Temp. controller
- 電源開關 Power S/W, 緊急開關 Emergency S/W, 計時器 Hour meter
- 過熱保護Over heat protector
- 透視窗Viewing window: 200*250
6) **裝置(Safety device)
- 漏電開關 Electric leakage breaker
- 過熱保護Over heat protector
- 循環電機過載繼電器Circulation motor over load relay: E.O.C.R
- 冷凍過載繼電器Refri. Over load relay
- 冷凍高低溫壓力開關 Refri. High/Low pressure S/W
- 故障信息 Trouble message
7) 記錄器(Recorder)
- 型號Model: SR-10001
- 制造公司 YOKOGAWA. JAPAN (100mm)
8) 電源(Power source) : AC380V / 50HZ 3Phase 18.0KW
9) Warranty
- In the free repair service
- 提供目錄 The manual offer
D. 其他事項(Remarks) ;
1) Original catalogue and specification are attached.
產品目錄及使用說明書附表。
2) Installation and a test-run should be performed by a qualified engineer.
設置及試運轉由專門領域的專家進行 。
3) one year warranty should be provided after the installation.
保修期為售后1年
4) Electrical service line contruction work to the installation on-site should
be done by the customer. 客戶負責把電線設置在設備安裝的位置。
5) IN-OUT piping work of water pipe system to the installation on-site should
be done by the customer. 需要供排水設施時，客戶負責把進出水管道設置在設備安裝的位置。
